stupidguy 发表于 2013-12-25 23:46:55

Good job, 繼續努力!

Ahrovan 发表于 2013-12-26 04:48:51

本帖最后由 Ahrovan 于 2013-12-26 04:49 编辑

CUBIEez installed in nand & i can not use network for connect to internet or use apt-get install command - driver is not ported ? or i can set or config that ?? thansk

matson 发表于 2013-12-26 12:42:47

Ahrovan 发表于 2013-12-26 04:48 static/image/common/back.gif
CUBIEez installed in nand & i can not use network for connect to internet or use apt-get install com ...

cb2 or ct?
try 'sudo ifconfig -a' command, to make sure there is 'eth0' net device.
the Ethernet should work

Ahrovan 发表于 2013-12-26 18:01:50

matson 发表于 2013-12-26 12:42 static/image/common/back.gif
cb2 or ct?
try 'sudo ifconfig -a' command, to make sure there is 'eth0' net device.
the Ethernet s ...CB2{-A20}
///
cubie@cubieez:~$ sudo su
password for cubie:
root@cubieez:/home/cubie# ifconfig
eth0      Link encap:EthernetHWaddr 02:07:08:02:85:00
          inet addr:192.168.1.124Bcast:192.168.1.255Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICASTMTU:1500Metric:1
          RX packets:5 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:320 (320.0 B)TX bytes:0 (0.0 B)
          Interrupt:87 Base address:0x4000

lo      Link encap:Local Loopback
          inet addr:127.0.0.1Mask:255.0.0.0
          UP LOOPBACK RUNNINGMTU:16436Metric:1
          RX packets:64 errors:0 dropped:0 overruns:0 frame:0
          TX packets:64 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:5184 (5.0 KiB)TX bytes:5184 (5.0 KiB)

root@cubieez:/home/cubie#
///
eth0 net device is ok,but i can not use internet with browser or command apt-get,is ip true? or not
thanks!

Ahrovan 发表于 2013-12-26 18:38:06

matson 发表于 2013-12-26 12:42 static/image/common/back.gif
cb2 or ct?
try 'sudo ifconfig -a' command, to make sure there is 'eth0' net device.
the Ethernet s ...

sunxi-gpio kernel module ::
can we use sunxi-gpio module in cubieez - this module ported into cubieez kernel ?
ex:
$ echo 1 > /sys/class/gpio/export
$ echo 2 > /sys/class/gpio/export
$ echo 3 > /sys/class/gpio/export
& can we use http://docs.cubieboard.org/tutorials/dvk521/documentations/a20/driver_porting_and_configuration
for cubieez ?
thanks !

matson 发表于 2013-12-26 20:34:27

Ahrovan 发表于 2013-12-26 18:01 static/image/common/back.gif
CB2{-A20}
///
cubie@cubieez:~$ sudo su


192.168.1.124 is set statictly, I think you need to change the /etc/network/interface config file, or just run the following command:
sudo dhclient eth0

CJH_cubietech 发表于 2013-12-26 20:35:46

擦,怎么ct 刷这个系统,我的 rapoo 8100 无线键盘不能用了。。。
usb 接收器上的小灯我按键时有反应啊~~:dizzy:
原来 lubuntu 下是可以用的~~

为什么~~

matson 发表于 2013-12-26 20:36:14

Ahrovan 发表于 2013-12-26 18:38 static/image/common/back.gif
sunxi-gpio kernel module ::
can we use sunxi-gpio module in cubieez - this module ported into cu ...

already builtin gpio_sunxi module

matson 发表于 2013-12-26 20:37:29

CJH_cubietech 发表于 2013-12-26 20:35 static/image/common/back.gif
擦,怎么ct 刷这个系统,我的 rapoo 8100 无线键盘不能用了。。。
usb 接收器上的小灯我按键时有反应啊~~:d ...

驱动太多了,所以去掉了一些。估计一个不小心把你要的那个驱动干掉了

CJH_cubietech 发表于 2013-12-26 20:44:21

matson 发表于 2013-12-26 20:37 static/image/common/back.gif
驱动太多了,所以去掉了一些。估计一个不小心把你要的那个驱动干掉了

意思就是我的键盘就不能用了??
我还有个rapoo 1800.pro 的无线键盘倒是能用,
有没有什么办法补救??
页: 1 [2] 3 4 5
查看完整版本: cb2/ct的debian固件 - debieez